Flagpoles are metal piping with thick enough walls (generally 1/4 inch thick or more) designed to withstand the wind load a flag exerts on the pole during high-wind weather conditions. Galvanized pipe is well-suited to such an application due to its resistance to the formation of rust, which could weaken the metal. Due to this resistance to rust, such pipe can be used as a permanent mast for flying a flag, where untreated steel pipe must be removed periodically and replaced with new pipe to replace a rusty, corroded section.
Flagpoles can be anywhere from a few feet to 100 feet in length. The actual pole is divided into sections for assembly, depending on the height. Flag poles between 30 and 35 feet can come in two sections whereas flag poles beyond 40 feet are made from three to five sections.This adds sturdiness and flexibility to a pole to keep it from collapsing during high winds. Flagpoles can be made of aluminum, steel, Plexiglass or fiberglass.
Selecting the right material for your flag pole largely depends on the wind speeds typical in your area and the purpose of the pole. Aluminum flagpoles are usually used for commercial displays while fiberglass poles are best for boats, homes and side-wall mounts. To fly flags on top of skyscrapers and other tall buildings, flagpoles are made of steel. Flagpole mounting is just as important as the construction of the pole. Flag poles are usually mounted inside a pole sleeve at a depth three times the diameter of the pole. The sleeve is surrounded by cement and sealed to prevent water damage and rust.
Allow the concrete to dry overnight. Take the pipe out of the concrete (it should come out easily due to the petroleum jelly. If you want, you can paint your pipe a different color to give it a more elegant look. Allow the paint to dry before putting the pipe back into the concrete. The pipe should fit perfectly in the concrete.
Thread rope through the pulleys and tie a knot in the rope just above the lower pulley. Connect a flag clip to the rope at this knot, then measure the correct distance to the position of the other flag clip hole on the flag and install another into position on the rope (measure the distance of the holes in the flag itself for accurate positioning of the clips for your particular flag). Dig a square hole where the mast is to be set, 4 feet deep and 2 feet wide. Set 4 feet of the 5-foot end into the hole and have a partner assist by holding the pipe in place, as straight as possible.
There is a barrage of cheap and Flagpoles being imported and sold, that do not comply with the statute. This is bad for a number of reasons. Imported flagpoles are cheaply made and more importantly, the designs, materials, colors, and methods do not compare well with the better quality, longer-lasting, and correctly designed flagpoles made by American manufacturers. The Flag Company Inc specialized in flags and flagpoles designs offered a special edition of flagpoles to comfort your environment with the genius American brand flagpoles that stay for centuries to memorize the history of flagpole production for the future.
Flagpoles can be anywhere from a few feet to 100 feet in length. The actual pole is divided into sections for assembly, depending on the height. Flag poles between 30 and 35 feet can come in two sections whereas flag poles beyond 40 feet are made from three to five sections.This adds sturdiness and flexibility to a pole to keep it from collapsing during high winds. Flagpoles can be made of aluminum, steel, Plexiglass or fiberglass.
Selecting the right material for your flag pole largely depends on the wind speeds typical in your area and the purpose of the pole. Aluminum flagpoles are usually used for commercial displays while fiberglass poles are best for boats, homes and side-wall mounts. To fly flags on top of skyscrapers and other tall buildings, flagpoles are made of steel. Flagpole mounting is just as important as the construction of the pole. Flag poles are usually mounted inside a pole sleeve at a depth three times the diameter of the pole. The sleeve is surrounded by cement and sealed to prevent water damage and rust.
Allow the concrete to dry overnight. Take the pipe out of the concrete (it should come out easily due to the petroleum jelly. If you want, you can paint your pipe a different color to give it a more elegant look. Allow the paint to dry before putting the pipe back into the concrete. The pipe should fit perfectly in the concrete.
Thread rope through the pulleys and tie a knot in the rope just above the lower pulley. Connect a flag clip to the rope at this knot, then measure the correct distance to the position of the other flag clip hole on the flag and install another into position on the rope (measure the distance of the holes in the flag itself for accurate positioning of the clips for your particular flag). Dig a square hole where the mast is to be set, 4 feet deep and 2 feet wide. Set 4 feet of the 5-foot end into the hole and have a partner assist by holding the pipe in place, as straight as possible.
There is a barrage of cheap and Flagpoles being imported and sold, that do not comply with the statute. This is bad for a number of reasons. Imported flagpoles are cheaply made and more importantly, the designs, materials, colors, and methods do not compare well with the better quality, longer-lasting, and correctly designed flagpoles made by American manufacturers. The Flag Company Inc specialized in flags and flagpoles designs offered a special edition of flagpoles to comfort your environment with the genius American brand flagpoles that stay for centuries to memorize the history of flagpole production for the future.
About the Author:
To see this item in real life do flagco.com, and after that order flagpoles from flagco.com for you.